 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HA1630D04/05/06 Series Ultra-Small Low Voltage Operation CMOS Dual Operational Amplifier REJ03D0801-0200 Rev.2.00 Feb 07, 2007 Description The HA1630D04/05/06 are high slew rate dual CMOS Operational Amplifiers realizing low voltage operation, low input offset voltage and low supply current. In addition to a low operating voltage from 1.8V, these device output can achieve full swing output voltage capability extending to either supply. Available in an ultra-small TSSOP-8 and MMPAK-8 package that occupy more small area against the SOP-8. Features * Low power and single supply operation * Low input offset voltage * Low supply current (per channel) VDD = 1.8 to 5.5 V VIO = 4.0 mV Max IDD = 200 A Typ (HA1630D04) IDD = 400 A Typ (HA1630D05) IDD = 800 A Typ (HA1630D06) SR = 2 V/s Typ (HA1630D04) SR = 4 V/s Typ (HA1630D05) SR = 8 V/s Typ (HA1630D06) VOH = 2.9 V Min (at VDD = 3.0 V) IIB = 1 pA Typ * High slew rate * Maximum output voltage * Low input bias current Ordering Information Type No. HA1630D04T HA1630D05T HA1630D06T HA1630D04MM HA1630D05MM HA1630D06MM Package Name TTP-8DA Package Code PTSP0008JC-B MMPAK-8 PLSP0008JC-A Rev.2.00 Feb 07, 2007 page 1 of 23 HA1630D04/05/06 Series Pin Arrangement VOUT1 1 VIN1(-) 2 VIN1(+) 3 VSS 4 -+ +- 8 VDD 7 VOUT2 6 VIN2(-) 5 VIN2(+) Equivalent Circuit (per one channel) VDD VIN(-) VIN(+) VOUT VSS Rev.2.00 Feb 07, 2007 page 2 of 23 HA1630D04/05/06 Series Absolute Maximum Ratings (Ta = 25C) Items Symbol Ratings Unit Note Supply voltage VDD 7 V Differential input voltage VIN(diff) -VDD to +VDD V Input voltage VIN -0.3 to +VDD V *1 Power dissipation PT 240/145 mW TTP-8DA/MMPAK-8 *2 Operating temp. Range Topr -40 to +85 C Storage temp. Range Tstg -55 to +125 C Notes: 1. Do not apply Input Voltage exceeding VDD or 7 V. 2. The value of PTSP0008JC-B (TTP-8DAV) / PLSP0008JC-A (MMPAK-8). It computes from heat resistance ja = 520C/W, and 690C/W each other. Electrical Characteristics (VDD = 3.0 V, Ta = 25C) Items Input offset voltage Input offset current Input bias current Output high voltage Output source current Symbol VIO IIO IIB VOH IO SOURCE Min -- -- -- Typ -- (1.0) (1.0) Max 4.0 -- -- Unit mV pA pA Test Condition Vin = 1.5 V Vin = 1.5 V Vin = 1.5 V RL = 100 k VOH = 2.5 V (HA1630D04) VOH = 2.5 V (HA1630D05) VOH = 2.5 V (HA1630D06) RL = 100 k VOL = 0.5 V (HA1630D04) VOL = 0.5 V (HA1630D05) VOL = 0.5 V (HA1630D06) (HA1630D04, HA1630D05) (HA1630D06) CL = 20 pF (HA1630D04) CL = 20 pF (HA1630D05) CL = 20 pF (HA1630D06) CL = 20 pF (HA1630D04) CL = 20 pF (HA1630D05) CL = 20 pF (HA1630D06) 2.9 -- -- V 100 200 -- A 200 400 -- 400 800 -- Output low voltage VOL -- -- 0.1 V Output sink current IO SINK -- (5.0) -- mA -- (6.0) -- -- (6.5) -- -0.05 to 2.1 -- -- V VCM Common mode input voltage range 0 to 1.9 -- -- Slew rate SR -- (2.0) -- V/s -- (4.0) -- -- (8.0) -- Voltage gain AV 60 90 -- dB Gain bandwidth product BW -- (2100) -- kHz -- (3300) -- -- (3600) -- Power supply rejection ratio PSRR 50 70 -- dB Common mode rejection ratio CMRR 50 70 -- dB Supply current IDD -- 400 800 A -- 800 1600 -- 1600 3400 Notes: 1. In the case of continuous current flow, use a sink current of under 4 mA. 2. ( ) : Design specification RL = (HA1630D04) RL = (HA1630D05) RL = (HA1630D06) Rev.2.00 Feb 07, 2007 page 3 of 23 HA1630D04/05/06 Series Table of Graphs Electrical Characteristics Supply current IDD vs Supply voltage vs Ambient temperature Output high voltage VOH vs Output source current vs Supply voltage Output source current IO SOURCE vs Ambient temperature Output low voltage VOL vs Output sink current Output sink current IO SINK vs Ambient temperature Input offset voltage VIO Distribution vs Supply voltage vs Ambient temperature vs Ambient temperature VCM Common mode input voltage range Power supply rejection ratio Common mode rejection ratio Voltage gain & phase angle Input bias current Slew Rate (rising) Slew Rate (falling) Slew rate PSRR CMRR AV IIB SRr SRf vs Frequency vs Frequency vs Frequency vs Ambient temperature vs Input voltage vs Ambient temperature vs Ambient temperature Large signal transient response Small signal transient response vs. Output voltage p-p vs. Output voltage p-p vs Frequency vs Frequency vs Frequency HA1630D04 Figure HA1630D05 Figure HA1630D06 Figure 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 1-21 1-22 1-23 1-24 1-25 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 2-24 2-25 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15 3-16 3-17 3-18 3-19 3-20 3-21 3-22 3-23 3-24 3-25 Test Circuit 2 4 6 5 6 1 7 1 7 10 3 9 Total harmonic distortion + noise Maximum p-p output voltage Voltage noise density Channel separation (0 dB) (40 dB) 8 Rev.2.00 Feb 07, 2007 page 4 of 23 HA1630D04/05/06 Series Main Characteristics (HA1630D04) Figure 1-1. HA1630D04 Supply Current vs. Supply Voltage 400 Supply Current IDD (A) Supply Current IDD (A) Ta = 25C Figure 1-2. HA1630D04 Supply Current vs. Ambient Temperature 400 VDD = 5.5 V 300 200 100 0 1 2 3 4 5 Supply Voltage VDD (V) 6 300 200 100 0 -40 VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 1-3. HA1630D04 Output High Voltage vs. Output Source Current Output High Voltage VOH (V) Output High Voltage VOH (V) Figure 1-4. HA1630D04 Output High Voltage vs. Supply Voltage 6 5 4 3 2 1 Ta = 25C VDD = 3.0 V RL = 100 k 6 5 4 3 VDD = 3.0 V VDD = 5.5 V Ta = 25C 2 1 0 0 100 200 300 Output Source Current IOSOURCE (A) VDD = 1.8 V 1 2 3 4 5 Supply Voltage VDD (V) 6 Figure 1-5. HA1630D04 Output Source Current vs. Ambient Temperature 400 Output Source Current IOSOURCE (A) VDD = 5.5 V 300 200 100 0 -40 VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Rev.2.00 Feb 07, 2007 page 5 of 23 HA1630D04/05/06 Series Figure 1-6. HA1630D04 Output Low Voltage vs. Output Sink Current Output Low Voltage VOL (V) Figure 1-7. HA1630D04 Output Sink Current vs. Ambient Temperature 10 Output Sink Current IOSINK (mA) VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 1.5 1.0 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 8 6 4 2 0 -40 0.5 0 0 2 4 Output Sink Current IOSINK (mA) 6 -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 1-8. HA1630D04 Input Offset Voltage Distribution Input Offset Voltage VIO (mV) Figure 1-9. HA1630D04 Input Offset Voltage vs. Supply Voltage 4 3 2 1 0 -1 -2 -3 -4 1 2 3 4 5 Supply Voltage VDD (V) 6 Ta = 25C VIN = 0.5 V 40 Ta = 25C VDD = 3.0 V Percentage (%) 30 20 10 0 -4 -3 -2 -1 0 1 2 3 Input Offset Voltage VIO (mV) 4 Figure 1-10. HA1630D04 Input Offset Voltage vs. Ambient Temperature Input Offset Voltage VIO (mV) Figure 1-11. HA1630D04 Common Mode Input Voltage vs. Ambient Temperature 3.0 Common Mode Input Voltage VCM (V) 4 3 2 1 0 -1 -2 -3 -4 -40 -20 0 20 40 60 80 100 VDD = 5.5 V, VIN = 2.75 V VDD = 1.8 V, VIN = 0.9 V VDD = 3.0 V, VIN = 1.5 V 2.0 VDD = 3.0 V 1.0 0 -1.0 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Rev.2.00 Feb 07, 2007 page 6 of 23 HA1630D04/05/06 Series Figure 1-12. HA1630D04 Power Supply Rejection Ratio vs. Frequency Power Supply Rejection Ratio PSRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 1-13. HA1630D04 Common Mode Rejection Ratio vs. Frequency Common Mode Rejection Ratio CMRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 1-14. HA1630D04 Open Loop Voltage Gain and Phase Angle vs. Frequency 100 Open Loop Voltage Gain AVOL (dB) 60 40 20 0 -20 -40 10 100 1k 10k Frequency f (Hz) 100k 1M Phase Angle Phase Margin: 57 deg 90 45 0 -45 -90 10M Rev.2.00 Feb 07, 2007 page 7 of 23 Phase Angle (deg) 80 Open Loop Voltage Gain Ta = 25C VDD = 3.0 V 180 RL = 1 M CL = 20 pF 135 225 HA1630D04/05/06 Series Figure 1-15. HA1630D04 Input Bias Current vs. Ambient Temperature Input Bias Current IIB (pA) VDD = 3.0 V Figure 1-16. HA1630D04 Input Bias Current vs. Input Voltage Input Bias Current IIB (pA) 200 100 0 -100 -200 200 100 0 -100 -200 Ta = 25C VDD = 3.0 V 0 25 50 75 Ambient Temperature Ta (C) 100 0 0.5 1.0 1.5 2.0 Input Voltage VIN (V) 2.5 3.0 Figure 1-17. HA1630D04 Slew Rate (rising) vs. Ambient Temperature 5 Slew Rate SRr (V/s) Figure 1-18. HA1630D04 Slew Rate (falling) vs. Ambient Temperature 5 Slew Rate SRf (V/s) VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 4 3 2 1 0 -40 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 4 3 2 1 0 -40 -20 0 20 40 60 80 100 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Figure 1-19. HA1630D04 Large Signal Transient Response 2.0 V Figure 1-20. HA1630D04 Small Signal Transient Response 1.6 V Vin = 2.1 Vp-p, 250 kHz 0V Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF Vin = 0.2 Vp-p, 250 kHz 1.4 V Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF 2.0 V 1.6 V 0V 1.4 V Rev.2.00 Feb 07, 2007 page 8 of 23 HA1630D04/05/06 Series Figure 1-21. HA1630D04 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 VDD = 3.0 V Ta = 25C Gain = 0 dB f = 10 kHz f = 1 kHz f = 100 Hz Figure 1-22. HA1630D04 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 T.H.D. + Noise (%) 1 0.1 0.01 0.001 T.H.D. + Noise (%) 1 0.1 0.01 V = 3.0 V DD Ta = 25C Gain = 40 dB f = 10 kHz f = 1 kHz f = 100 Hz 0.001 0 0.5 1.0 1.5 2.0 2.5 3.0 0 Output Voltage Vout p-p (V) 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage Vout p-p (V) Figure 1-23. HA1630D04 Voltage Output p-p vs. Frequency Voltage Output Vout p-p (V) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1k 10k 100k Frequency f (Hz) 1M Gain = 40 dB, VIN = 0.03 Vp-p Gain = 20 dB, VIN = 0.3 Vp-p Ta = 25C VDD = 3.0 V Gain = 0 dB, VIN = 2.0 Vp-p 10M Figure 1-24. HA1630D04 Voltage Noise Density vs. Frequency Figure 1-25. HA1630D04 Channel Separation vs. Frequency Voltage Noise Density (nVms/Hz) 160 120 80 40 0 100 VDD = 3.0 V Ta = 25C Gain = 40 dB RS = 1 k Channel Separation C.S (dB) 200 140 120 100 80 60 40 VDD = 3.0 V Ta = 25C CH1CH2 CH2CH1 20 RL = 1 M 0 100 CL = 20 pF 1k Frequency f (Hz) 10k 1k 10k 100k 1M 10M Frequency f (Hz) Rev.2.00 Feb 07, 2007 page 9 of 23 HA1630D04/05/06 Series Main Characteristics (HA1630D05) Figure 2-1. HA1630D05 Supply Current vs. Supply Voltage 800 Supply Current IDD (A) Supply Current IDD (A) Ta = 25C Figure 2-2. HA1630D05 Supply Current vs. Ambient Temperature 800 600 400 200 0 -40 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 600 400 200 0 1 2 3 4 5 Supply Voltage VDD (V) 6 -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 2-3. HA1630D05 Output High Voltage vs. Output Source Current Output High Voltage VOH (V) Ta = 25C VDD = 5.5 V Figure 2-4. HA1630D05 Output High Voltage vs. Supply Voltage Output High Voltage VOH (V) 6 5 4 3 VDD = 3.0 V 6 5 4 3 2 1 Ta = 25C VDD = 3.0 V RL = 100 k RL = 20 k 2 1 0 0 100 200 300 400 500 Output Source Current IOSOURCE (A) VDD = 1.8 V 1 2 3 4 5 Supply Voltage VDD (V) 6 Figure 2-5. HA1630D05 Output Source Current vs. Ambient Temperature 800 Output Source Current IOSOURCE (A) VDD = 5.5 V 600 400 200 0 -40 VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Rev.2.00 Feb 07, 2007 page 10 of 23 HA1630D04/05/06 Series Figure 2-6. HA1630D05 Output Low Voltage vs. Output Sink Current Output Low Voltage VOL (V) Figure 2-7. HA1630D05 Output Sink Current vs. Ambient Temperature 10 Output Sink Current IOSINK (mA) VDD = 5.5 V VDD = 3.0 V 1.5 8 6 4 2 0 -40 1.0 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 0.5 VDD = 1.8 V 0 0 2 4 6 Output Sink Current IOSINK (mA) 8 -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 2-8. HA1630D05 Input Offset Voltage Distribution Input Offset Voltage VIO (mV) Figure 2-9. HA1630D05 Input Offset Voltage vs. Supply Voltage 4 3 2 1 0 -1 -2 -3 -4 1 2 3 4 5 Supply Voltage VDD (V) 6 Ta = 25C VIN = 0.5 V 40 Ta = 25C VDD = 3.0 V Percentage (%) 30 20 10 0 -4 -3 -2 -1 0 1 2 3 Input Offset Voltage VIO (mV) 4 Figure 2-10. HA1630D05 Input Offset Voltage vs. Ambient Temperature Input Offset Voltage VIO (mV) Figure 2-11. HA1630D05 Common Mode Input Voltage vs. Ambient Temperature 3.0 Common Mode Input Voltage VCM (V) 4 3 2 1 0 -1 -2 -3 -4 -40 -20 0 20 40 60 80 100 VDD = 5.5 V, VIN = 2.75 V VDD = 1.8 V, VIN = 0.5 V VDD = 3.0 V, VIN = 1.5 V 2.0 VDD = 3.0 V 1.0 0 -1.0 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Rev.2.00 Feb 07, 2007 page 11 of 23 HA1630D04/05/06 Series Figure 2-12. HA1630D05 Power Supply Rejection Ratio vs. Frequency Power Supply Rejection Ratio PSRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 2-13. HA1630D05 Common Mode Rejection Ratio vs. Frequency Common Mode Rejection Ratio CMRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 2-14. HA1630D05 Open Loop Voltage Gain and Phase Angle vs. Frequency 100 Open Loop Voltage Gain AVOL (dB) 225 Open Loop Voltage Gain 60 40 20 0 -20 -40 10 100 1k 10k Frequency f (Hz) 100k 1M Phase Angle Phase Margin: 55 deg 90 45 0 -45 -90 10M Rev.2.00 Feb 07, 2007 page 12 of 23 Phase Angle (deg) 80 Ta = 25C VDD = 3.0 V 180 RL = 1 M CL = 20 pF 135 HA1630D04/05/06 Series Figure 2-15. HA1630D05 Input Bias Current vs. Ambient Temperature Input Bias Current IIB (pA) Input Bias Current IIB (pA) Figure 2-16. HA1630D05 Input Bias Current vs. Input Voltage 200 100 0 -100 -200 Ta = 25C VDD = 3.0 V 200 VDD = 3.0 V 100 0 -100 -200 0 25 50 75 Ambient Temperature Ta (C) 100 0 0.5 1.0 1.5 2.0 Input Voltage VIN (V) 2.5 3.0 Figure 2-17. HA1630D05 Slew Rate (rising) vs. Ambient Temperature 10 Slew Rate SRr (V/s) Figure 2-18. HA1630D05 Slew Rate (falling) vs. Ambient Temperature 10 Slew Rate SRf (V/s) VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 8 6 4 2 0 -40 VDD = 1.8 V VDD = 5.5 V VDD = 3.0 V 8 6 4 2 0 -40 -20 0 20 40 60 80 100 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Figure 2-19. HA1630D05 Large Signal Transient Response Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF 1.6 V Figure 2-20. HA1630D05 Small Signal Transient Response Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF 2.0 V VIN = 2.1 Vp-p, 500 kHz 0V VIN = 0.2 Vp-p, 500 kHz 1.4 V 2.0 V 1.6 V 0V 1.4 V Rev.2.00 Feb 07, 2007 page 13 of 23 HA1630D04/05/06 Series Figure 2-21. HA1630D05 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 VDD = 3.0 V Ta = 25C Gain = 0 dB f = 10 kHz f = 1 kHz f = 100 Hz Figure 2-22. HA1630D05 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 f = 10 kHz f = 1 kHz f = 100 Hz T.H.D. + Noise (%) 1 0.1 0.01 0.001 0 T.H.D. + Noise (%) 1 0.1 0.01 V = 3.0 V DD Ta = 25C Gain = 40 dB 0.001 0.5 1.0 1.5 2.0 2.5 3.0 0 Output Voltage Vout p-p (V) 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage Vout p-p (V) Figure 2-23. HA1630D05 Voltage Output p-p vs. Frequency Voltage Output Vout p-p (V) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1k 10k 100k Frequency f (Hz) 1M Gain = 40 dB, VIN = 0.03 Vp-p Gain = 20 dB, VIN = 0.3 Vp-p Ta = 25C VDD = 3.0 V Gain = 0 dB, VIN = 2.0 Vp-p 10M Figure 2-24. HA1630D05 Voltage Noise Density vs. Frequency Figure 2-25. HA1630D05 Channel Separation vs. Frequency Voltage Noise Density (nVms/Hz) 160 120 80 40 0 100 VDD = 3.0 V Ta = 25C Gain = 40 dB RS = 1 k Channel Separation C.S (dB) 200 140 120 100 80 60 40 VDD = 3.0 V Ta = 25C CH1CH2 CH2CH1 20 RL = 1 M 0 100 CL = 20 pF 1k Frequency f (Hz) 10k 1k 10k 100k 1M 10M Frequency f (Hz) Rev.2.00 Feb 07, 2007 page 14 of 23 HA1630D04/05/06 Series Main Characteristics (HA1630D06) Figure 3-1. HA1630D06 Supply Current vs. Supply Voltage 1600 Supply Current IDD (A) Supply Current IDD (A) Ta = 25C Figure 3-2. HA1630D06 Supply Current vs. Ambient Temperature 1600 VDD = 5.5 V 1200 800 400 0 1 2 3 4 5 Supply Voltage VDD (V) 6 1200 800 400 0 -40 VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 3-3. HA1630D06 Output High Voltage vs. Output Source Current Output High Voltage VOH (V) Output High Voltage VOH (V) Figure 3-4. HA1630D06 Output High Voltage vs. Supply Voltage 6 5 4 3 2 1 RL = 20 k Ta = 25C RL = 100 k 6 5 VDD = 5.5 V 4 VDD = 3.0 V Ta = 25C 3 2 1 0 0 200 400 600 800 1000 Output Source Current IOSOURCE (A) VDD = 1.8 V 1 2 3 4 5 Supply Voltage VDD (V) 6 Figure 3-5. HA1630D06 Output Source Current vs. Ambient Temperature 1600 Output Source Current IOSOURCE (A) VDD = 5.5 V 1200 800 400 0 -40 VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Rev.2.00 Feb 07, 2007 page 15 of 23 HA1630D04/05/06 Series Figure 3-6. HA1630D06 Output Low Voltage vs. Output Sink Current Output Low Voltage VOL (V) Figure 3-7. HA1630D06 Output Sink Current vs. Ambient Temperature 12 Output Sink Current IOSINK (mA) VDD = 5.5 V VDD = 3.0 V 1.5 10 8 6 4 2 1.0 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 0.5 VDD = 1.8 V 0 0 0.2 0.4 0.6 0.8 Output Sink Current IOSINK (mA) 1.0 0 -40 -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 3-8. HA1630D06 Input Offset Voltage Distribution Input Offset Voltage VIO (mV) Figure 3-9. HA1630D06 Input Offset Voltage vs. Supply Voltage 4 3 2 1 0 -1 -2 -3 -4 1 2 3 4 5 Supply Voltage VDD (V) 6 Ta = 25C VIN = 0.5 V 40 Ta = 25C VDD = 3.0 V Percentage (%) 30 20 10 0 -4 -3 -2 -1 0 1 2 3 Input Offset Voltage VIO (mV) 4 Figure 3-10. HA1630D06 Input Offset Voltage vs. Ambient Temperature Input Offset Voltage VIO (mV) Figure 3-11. HA1630D06 Common Mode Input Voltage vs. Ambient Temperature 3.0 Common Mode Input Voltage VCM (V) 4 3 2 1 0 -1 -2 -3 -4 -40 -20 0 20 40 60 80 100 VDD = 5.5 V, VIN = 2.75 V VDD = 1.8 V, VIN = 0.5 V VDD = 3.0 V, VIN = 1.5 V 2.0 VDD = 3.0 V 1.0 0 -1.0 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Rev.2.00 Feb 07, 2007 page 16 of 23 HA1630D04/05/06 Series Figure 3-12. HA1630D06 Power Supply Rejection Ratio vs. Frequency Power Supply Rejection Ratio PSRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 3-13. HA1630D06 Common Mode Rejection Ratio vs. Frequency Common Mode Rejection Ratio CMRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 3-14. HA1630D06 Open Loop Voltage Gain and Phase Angle vs. Frequency 100 Open Loop Voltage Gain AVOL (dB) 225 Phase Angle (deg) Open Loop Voltage Gain Ta = 25C VDD = 3.0 V 180 RL = 1 M CL = 20 pF 135 80 60 40 20 0 -20 -40 10 100 1k Phase Angle 90 45 Phase Margin: 65 deg 0 -45 10k Frequency f (Hz) 100k 1M -90 10M Rev.2.00 Feb 07, 2007 page 17 of 23 HA1630D04/05/06 Series Figure 3-15. HA1630D06 Input Bias Current vs. Ambient Temperature Input Bias Current IIB (pA) Input Bias Current IIB (pA) Figure 3-16. HA1630D06 Input Bias Current vs. Input Voltage 200 Ta = 25C VDD = 3.0 V 200 VDD = 3.0 V 100 0 -100 -200 100 0 -100 -200 0 25 50 75 Ambient Temperature Ta (C) 100 0 0.5 1.0 1.5 2.0 Input Voltage VIN (V) 2.5 3.0 Figure 3-17. HA1630D06 Slew Rate (rising) vs. Ambient Temperature 14 Slew Rate SRr (V/s) Figure 3-18. HA1630D06 Slew Rate (falling) vs. Ambient Temperature 14 Slew Rate SRf (V/s) 12 10 8 6 4 -40 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 12 10 8 6 4 -40 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 100 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Figure 3-19. HA1630D06 Large Signal Transient Response 2.0 V Figure 3-20. HA1630D06 Small Signal Transient Response 1.6 V VIN = 1.9 Vp-p, 500 kHz 0V Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF VIN = 0.2 Vp-p, 500 kHz 1.4 V Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF 2.0 V 1.6 V 0V 1.4 V Rev.2.00 Feb 07, 2007 page 18 of 23 HA1630D04/05/06 Series Figure 3-21. HA1630D06 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 VDD = 3.0 V Ta = 25C Gain = 0 dB Figure 3-22. HA1630D06 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 T.H.D. + Noise (%) 1 0.1 0.01 0.001 0 T.H.D. + Noise (%) 1 0.1 0.01 V = 3.0 V DD Ta = 25C Gain = 40 dB f = 10 kHz f = 1 kHz f = 100 Hz f = 10 kHz f = 1 kHz f = 100 Hz 0.001 0.5 1.0 1.5 2.0 2.5 3.0 0 Output Voltage Vout p-p (V) 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage Vout p-p (V) Figure 3-23. HA1630D06 Voltage Output p-p vs. Frequency Voltage Output Vout p-p (V) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1k 10k 100k Frequency f (Hz) 1M Gain = 40 dB, VIN = 0.03 Vp-p Gain = 20 dB, VIN = 0.3 Vp-p Ta = 25C VDD = 3.0 V Gain = 0 dB, VIN = 2.0 Vp-p 10M Figure 3-24. HA1630D06 Voltage Noise Density vs. Frequency Figure 3-25. HA1630D06 Channel Separation vs. Frequency Voltage Noise Density (nVms/Hz) 160 120 80 40 0 100 VDD = 3.0 V Ta = 25C Gain = 40 dB RS = 1 k Channel Separation C.S (dB) 200 140 120 100 80 60 40 VDD = 3.0 V Ta = 25C CH1CH2 CH2CH1 20 RL = 1 M 0 100 1k CL = 20 pF 1k Frequency f (Hz) 10k 10k 100k 1M 10M Frequency f (Hz) Rev.2.00 Feb 07, 2007 page 19 of 23 HA1630D04/05/06 Series Test Circuits 1. Power Supply Rejection Ratio, PSRP & Voltage Offset, VIO VDD RF = 680 k RS = 6.8 k - + VDD 2 RS = 6.8 k PSRR VO PSRR = -20log VDD1 - VDD2 VO1 - VO2 x RS R S + RF VIO VIO = VO - VDD 2 x RS R S + RF Measure VO corresponding to VDD1 = 2.95 V and VDD2 = 3.05 V 2. Supply Current, IDD VDD A - + VDD 2 VDD 2 A - + 3. Input Bias Current, IIB VDD 4. Output High Voltage, VOH VDD VOH VIN1 = VDD / 2 - 0.05 V VIN2 = VDD / 2 + 0.05 V - + VIN1 VIN2 VO RL = 100 k 5. Output Low Voltage, VOL VDD VOL VIN1 = VDD / 2 + 0.05 V VIN2 = VDD / 2 - 0.05 V RL = 100 k VO - + VIN1 VIN2 Rev.2.00 Feb 07, 2007 page 20 of 23 HA1630D04/05/06 Series 6. Output Source Current, IOSOURCE & Output Sink Current, IOSINK VDD IOSOURCE VO = VDD - 0.5 V VIN1 = VDD / 2 - 0.05 V VIN2 = VDD / 2 + 0.05 V A VO IOSINK VO = + 0.5 V VIN1 = VDD / 2 + 0.05 V VIN2 = VDD / 2 - 0.05 V - + VIN1 VIN2 7. Common Mode Input Voltage, VCM & Common Mode Rejection Ratio, CMRR VDD RF = 680 k RS = 6.8 k - + CMRR = -20log VO VIN1 - VIN2 VO1 - VO2 x RS RS + RF CMRR RS = 6.8 k VIN VDD 2 RF = 680 k 8. Total Harmonic Distortion, THD VDD Gain Variable RS VIN RF - + Measure VO corresponding to VIN1 = 1.45 V and VIN2 = 1.55 V THD Gain Variable RF / RS = 20log (100 k / 1 k) = 40 dB RF / RS = 20log (100 k / 100 k) = 0 dB freq = 100 Hz, 1 kHz, 10 kHz 30 kHz LPF ON VO VSS 9. Slew Rate, SR VDD 10. Gain, AV & Phase, GBW VDD RF = 680 k - + 1 M RS = 6.8 k VO 20 pF - + 1 M VO 20 pF VSS RS = 6.8 k VSS Rev.2.00 Feb 07, 2007 page 21 of 23 HA1630D04/05/06 Series Package Dimensions JEITA Package Code P-TSSOP8-4.4x3-0.65 RENESAS Code PTSP0008JC-B Previous Code TTP-8DAV MASS[Typ.] 0.034g *1 D 5 F 8 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. bp HE E *2 Terminal cross section ( Ni/Pd/Au plating ) Index mark c Reference Dimension in Millimeters Symbol L1 1 Z e 4 *3 bp x M A A1 L Detail F y D E A2 A1 A bp b1 c c1 HE e x y Z L L1 Min Nom Max 3.00 3.30 4.40 0.03 0.07 0.10 1.10 0.15 0.20 0.25 0.10 0.15 0.20 0 8 6.20 6.40 6.60 0.65 0.13 0.10 0.805 0.40 0.50 0.60 1.00 Package Name MMPAK-8 JEITA Package Code P-LSOP8-2.8 x 2.95 - 0.65 RENESAS Code PLSP0008JC-A Previous Code MASS[Typ.] 0.02 g Unit: mm 0.13 +0.12 -0.03 2.95 0.2 4.0 0.3 2.8 0.1 0 to 0.1 0.65 1.95 0.1 M 0.2 1.1 0.1 0.3 0.1 Rev.2.00 Feb 07, 2007 page 22 of 23 0.6 +0.1 -0.05 HA1630D04/05/06 Series Taping & Reel Specification [Taping] Package Code TSSOP-8 MMPAK-8 W 12 12 P 8 4.0 Ao 6.9 3.15 Bo 3.6 4.35 Ko 1.7 -- E 1.75 -- 4.0 2.0 F 5.5 5.5 D1 1.5 1.05 Maximum Storage No. 3,000 pcs/reel 3,000 pcs/reel 1.75 Unit: mm 1.5 Cover Tape A0 F K0 B0 P Tape withdraw direction D1 W W1 [Ordering Information] Ordering Unit 3,000 pcs 2.0 2.0 W2 Mark Indication TSSOP-8 Product Name 0D04: HA1630D04 0D05: HA1630D05 0D06: HA1630D06 MMPAK-8 Product Name D04: HA1630D04 D05: HA1630D05 D06: HA1630D06 0D04 Trace Code D04 Trace Code Rev.2.00 Feb 07, 2007 page 23 of 23 A [Reel] Package TSSOP-8 MMPAK-8 Tape width 12 12 W1 17.4 17.0 W2 13.4 13.0 A 330 178 13.0 0.5 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 http://www.renesas.com Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 (c) 2007. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.0 |
Price & Availability of HA1630D06
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |